Project File:Channel Routing � Optional

3.7.1 Required Inputs

The following cards are REQUIRED for the simulation of channel routing.

Card	Argument	Description
DIFFUSIVE_WAVE	none	Specifies explicit diffusive-wave 1-D channel routing.
CHAN_EXPLIC	none	Specifies explicit diffusive-wave 1-D channel routing. Performs same function as DIFFUSIVE_WAVE.
CHANNEL_INPUT "filename.cif"	file name	Input ASCII file containing channel network connectivity and cross-sectional information for each link/node.
STREAM_CELL "filename.gst"	file name	Input ASCII file containing channel/grid connectivity information.
OUTLET_HYDRO "filename.otl"	file name	Output ASCII file containing discharge (m³ s^-1) unless QOUT_CFS flag is specified (ft³ s^-1)
SECTION_TABLE "filename.ext"	file name	Input ASCII file containing cross-section information for irregular, break-point channel cross-sections. REQUIRED if look-up table cross-sections are specified in the CHANNEL_INPUT file.

3.7.2 Initial Condition and Boundary Condition - Optional

Card	Argument	Description
EXPLIC_BACKWATER "filename.ext"	file name	Save explicit channel routing end of run values of channel depth (m) and discharge (m³ s^-1) for each cell.
EXPLIC_HOTSTART "filename.ext"	file name	Start explicit channel calculations using the values of channel depth and flow in the named file.
WRITE_CHAN_HOTSTART "filename"	file name	Save explicit channel routing end of run values of channel depth (m) and discharge (m³ s^-1) for each cell. Depths and discharges will be saved in separate files. Depths will be saved in a file with name "filename" with extension .dht. Discharges will be saved in a file with name "filename" with extension .qht.
READ_CHAN_HOTSTART "filename"	file name	Start explicit channel calculations using the values of channel depth and flow in the named file. Depths should be in a file with the name "filename" with extension .dht. Discharges should be in a file with the name "filename" and with extension .qht.
OVERBANK_FLOW	none	Allow water in channel to flow back onto overland flow plane when stream elevation is above top of bank and the adjacent overland cell elevation.
OVERBANK_MAX_DV	float	Fraction of stream water above TOB that can exit the channel during a single time step when the OVERBANK_FLOW card is specified. Defualt value is 0.01.
OVERLAND_BACKWATER	none	Include backwater effects on overland when stream water surface elevation or TOB is greater than overland flow surface elevation without allowing water in channel to flow back onto overland.
CHAN_POINT_INPUT	file name	Input ASCII file containing the point source input location, discharge, and concentrations.
MAX_COURANT_NUMBER	float	Value to limit maximum fractional change in channel volume for stability. Default is 0.04.

3.7.3 Stream Losses/Gains - Optional

3.7.3.1 General

Card	Argument	Units	Description
STREAM_LOSS	none	none	Card is used to specify that stream losses be computed when the WATER_TABLE card is not included in the project file.

3.7.3.2 Parameters

Used with WATER_TABLE or STREAM_LOSS card. These parameters may also be distributed along the channel by assigning in the CHAN_INPUT file.

Card	Argument	Units	Description
K_RIVER ##.##	real	cm hr^-1	Uniform hydraulic conductivity of streambed material. REQUIRES WATER_TABLE or STREAM_LOSS. May also be distributed in CHAN_INPUT file.
M_RIVER ##.##	real	cm	Uniform thickness of streambed material. Requires WATER_TABLE or STREAM_LOSS. May also be distributed in CHAN_INPUT file.

3.7.4 Optional Output

Card	Argument	Description
IN_HYD_LOCATION "filename.ihl"	table name	Input ASCII file specifying link/node pairs to write out time series data specified by OUT_HYD_LOCATION, OUT_DEP_LOCATION, or OUT_CON_LOCATION.
OUT_HYD_LOCATION "filename.ohl"	filename	Filename to output time series discharge data (m³ s^-1 or ft³ s^-1) at points specified in IN_HYD_LOCATION. REQUIRED if IN_HYD_LOCATION was specified.
OUT_DEP_LOCATION "filename.odl"	filename	Filename to output channel depths (m) every HYD_FREQ time steps at locations specified in the IN_HYD_LOCATION file.
IN_SED_LOC "filename.isl"	table name	Input ASCII file containing a list of internal link/node locations where the user wants to save sediment hydrographs. Format identical to IN_HYD_LOC option. REQUIRES SOIL_EROSION.
OUT_SED_LOC "filename.osl"	filename	Filename to output sediment flux hydrographs every HYD_FREQ time steps at internal catchment locations specified in the IN_SED_LOC file. REQUIRED if SOIL_EROSION and IN_SED_LOC card are specified.
IN_GWFLUX_LOCATION "filename.igf"	table name	Input ASCII file specifying link/node pairs to write out time series of stream/groundwater exchange flux in the file OUT_GWFLUX_LOCATION.
OUT_HYD_LOCATION "filename.ogf"	filename	Filename to output time series stream/groundwater exchange flux data (m² s^-1 or ft³ s^-1) at points specified in IN_GWFLUX_LOCATION. REQUIRED if IN_GWFLUX_LOCATION was specified.
STRICT_JULIAN_DATE	none	Specifies all time series data use strict Julian format.
CHAN_DEPTH "filename.cdp"	filename	Filename to output link/node data of channel depth (m) every MAP_FREQ time steps.
CHAN_STAGE "filename.cds"	filename	Filename to output link/node data of channel stage (m) every MAP_FREQ time steps.
CHAN_DISCHARGE "filename.cdq"	filename	Filename to output link/node data of channel discharge (m³ s^-1) every MAP_FREQ time steps.
CHAN_VELOCITY "filename.cdv"	filename	Filename to output link/node data of channel velocity (m s^-1) every MAP_FREQ time steps.
LAKE_OUTPUT "filename.lel"	filename	Filename to output reservoir elevation (m) and volume (m³) for each reservoir in the order listed in the .cif file every MAP_FREQ time steps.